A new study from Stanford researchers suggests that electricity generated by all of the world’s installed solar photovoltaic (PV) panels has caught up to the amount of energy going into the production of those panels, making the global solar photovoltaic industry a net energy producer. The results suggest that the PV industry was a net consumer of electricity as recently as 2010, but there is a >50% that in 2012 the PV industry was a net electricity provider and will “payback” the electrical energy required for its early growth before 2020.
The rapid growth of the solar power industry over the past decade may have exacerbated the global warming situation it was meant to soothe, simply because most of the energy used to manufacture the millions of solar panels came from burning fossil fuels. That irony, according to Stanford University researchers, is coming to an end.
For the first time since the boom started, the electricity generated by all of the world’s installed solar photovoltaic (PV) panels last year probably surpassed the amount of energy going into fabricating more modules, according to Michael Dale, a postdoctoral fellow at Stanford’s Global Climate & Energy Project (GCEP). With continued technological advances, the global PV industry is poised to pay off its debt of energy as early as 2015, and no later than 2020.
“This analysis shows that the industry is making positive strides,” said Dale, who developed a novel way of assessing the industry’s progress globally in a study published in the current edition of Environmental Science & Technology. “Despite its fantastically fast growth rate, PV is producing – or just about to start producing – a net energy benefit to society.”
The achievement is largely due to steadily declining energy inputs required to manufacture and install PV systems, according to co-author Sally Benson, GCEP’s director. The new study, Benson said, indicates that the amount of energy going into the industry should continue to decline, while the issue remains an important focus of research.
“GCEP is focused on developing game-changing energy technologies that can be deployed broadly. If we can continue to drive down the energy inputs, we will derive greater benefits from PV,” she said. “Developing new technologies with lower energy requirements will allow us to grow the industry at a faster rate.”
The energy used to produce solar panels is intense. The initial step in producing the silicon at the heart of most panels is to melt silica rock at 3,000 degrees
As investment and technological development have risen sharply with the number of installed panels, the energetic costs of new PV modules have declined. Thinner silicon wafers are now used to make solar cells, less highly refined materials are now used as the silicon feedstock, and less of the costly material is lost in the manufacturing process. Increasingly, the efficiency of solar cells using thin film technologies that rely on earth-abundant materials such as copper, zinc, tin and carbon have the potential for even greater improvements.
To be considered a success – or simply a positive energy technology – PV panels must ultimately pay back all the energy that went into them, said Dale. The PV industry ran an energy deficit from 2000 to now, consuming 75 percent more energy than it produced just five years ago. The researchers expect this energy debt to be paid off as early as 2015, thanks to declining energy inputs, more durable panels and more efficient conversion of sunlight into electricity.
If current rapid growth rates persist, by 2020 about 10 percent of the world’s electricity could be produced by PV systems. At today’s energy payback rate, producing and installing the new PV modules would consume around 9 percent of global electricity. However, if the energy intensity of PV systems continues to drop at its current learning rate, then by 2020 less than 2 percent of global electricity will be needed to sustain growth of the industry.
This may not happen if special attention is not given to reducing energy inputs. The PV industry’s energetic costs can differ significantly from its financial costs. For example, installation and the components outside the solar cells, like wiring and inverters, as well as soft costs like permitting, account for a third of the financial cost of a system, but only 13 percent of the energy inputs. The industry is focused primarily on reducing financial costs.
Continued reduction of the energetic costs of producing PV panels can be accomplished in a variety of ways, such as using less materials or switching to producing panels that have much lower energy costs than technologies based on silicon. The study’s data covers the various silicon-based technologies as well as newer ones using cadmium telluride and copper indium gallium diselenide as DOI: 10.1021/es3038824
InfEneTy is a knowledge platform which showcases critical news, insights and features on contemporary and topical issues related to Infrastructure, Energy and Technology affecting the economy, industry sectors, business environment. The intent is to enable an association with the evolving scenario and be a catalyst for change. Help make InfEneTy better. Share your comments or connect with us at firstname.lastname@example.org